Welcome to the AMTA paper archive. Select a category, publication date or search by author.
(Note: Papers will always be listed by categories. To see ALL of the papers meeting your search criteria select the "AMTA Paper Archive" category after performing your search.)
Specular reflectance data of indoor interior materials is a prerequisite to analysis of the channel characteristics for new millimeter and submillimeter indoor wireless communications. Antenna property such as gain and radiation pattern is one of the key measurement quantities in electromagnetic wave metrology. This paper describes a specular reflectance and antenna property measurement system and shows measurement results of the specular reflectance of an Acetal plate and the antenna property of a 24 dB horn antenna in 325-500 GHz frequency range.
Non-destructive testing (NDT) is a fundamental step in the production chain of aircraft structural components since it can save both money and time in product evaluation and troubleshooting. This paper presents a reflection-based imaging technique for electromagnetic (EM) testing of composite panels, with the device under test (DUT) being metal backed and both the transmitting and receiving components of the NDT system situated on the same side of the DUT. One of the key properties of the presented technique is the complete redundancy of a reference measurement, thereby making it feasible to retrieve a high quality image of the DUT with only a single measurement. Data for both a proof-of-concept DUT and an industrially manufactured composite panel is provided, and the retrieved images show the applicability of both the measurement technique and the imaging algorithms.
This paper presents a way to determine mutual coupling effects through analysis of the active voltage standing wave ratio (VSWR) to predict the presence of large reverse power levels in co-located multiple input multiple output (MIMO) radars in transmit mode. The methodology consists of measuring the forward and reverse waves on a dual directional coupler (DDC) to directly obtain the active reflection coefficient on a co-located MIMO radar system. The active VSWR of each individual antenna is computed from measurements of the active reflection coefficient. These results are compared against analytical methodologies.
The use of mode filtering to improve the quality of antenna measurements taken in non-anechoic environments is well known, [1, 2, 3, 4, 5]. In the far-field case [6, 7, 8], it has been shown that it is possible to use standard cylindrical near-field theory [8] to implement the necessary mode filtering using a singularly polarized, great circle, far-field pattern cut consisting of amplitude and phase data. The careful verification of this technique using a compact antenna test range (CATR) was reported in [7, 8] however that implementation had, as a prerequisite, the need to acquire the far-field data on a monotonic and equally spaced pattern abscissa. In many instances this is not convenient or perhaps impossible. This paper presents a recent development which allows data to be processed rigorously when having been acquired using an unequally spaced angular abscissa. This paper sets out the novel, far more sophisticated, algorithm together with results of actual range measurements that were processed using this new technique.
The Plane Wave Generator (PWG) is an array of elements with suitably optimized complex coefficients, generating a plane wave in the close proximity of the array. Thus, the PWG achieve far-field testing conditions in a Quiet Zone (QZ) at a reduced distance in a manner similar to what is achieved in a Compact Antenna Test Range (CATR) [1]. In this paper, the concept of a high performance, dual polarized PWG supporting up to 10:1 bandwidth is presented for the first time. A prototype of a dual polarized PWG has been designed, manufactured and tested in the 600MHz to 6GHz frequency range. The initial testing results on QZ uniformity and evaluation of possible measurement accuracy are presented.
The unknown-thru calibration technique is being used to achieve a system level calibration at millimeter wave frequencies (>50 GHz) on the robotic ranges at NIST. This two-port calibration requires the use of a full bi-directional measurement, instead of a traditional single-direction antenna measurement. We explored the value of the additional data acquired. We find that we can use this information to verify antenna/scan alignment, image the scattering from the positioner/facility, and perform a first order correction to the transmission data for uncertainties due to LO cable flexure.
We present a preliminary study of a modal (partial wave) expansion of the field used to characterize a propagation channel. We assume that the measurements of the scalar, two-dimensional field from which the modal expansion coefficients are obtained, contain Gaussian phase noise with zero mean. Three spatial sampling patterns of the field are considered. We find that the accuracy of the reconstructed field is strongly influenced by the spatial sampling pattern.
Rock core specimens collected during surveys for oil drilling have, in a standard form, a 4" diameter. Cores are cut in half or in 1/3-2/3 sections to provide core slab. We developed a measurement procedure based on spot probe illumination to characterize geological and/or geochemical properties of core slab specimens via their complex permittivity for frequencies between 2.5 GHz and 20 GHz. Conventional reflectometer methods are based on illumination of a thin slab of air-or metal-backed material. However, in this case only the front surface is flat and the back surface is semicircular. A measurement method was developed based on time-domain gating to separate the back-surface reflection from that of the front. Material inversion is then based on the amplitude and phase of the reflection just from the front surface. This paper presents details of the calibration for this reflectometer measurement method, along with example measurements of core slab materials. Two different inversion methods are applied to these measured data. The first is a more conventional frequency-by-frequency method for inverting complex permittivity from the amplitude and phase of the reflection. The second method applies a physical model, the Debye relaxation model, to the data. This model-based approach minimizes the errors from edge diffraction from the small sample size.
In this paper, we explore the capabilities of the Monostatic-Bistatic Theorem (MBT) applied to Radar Cross Section (RCS) in low frequency. Originally, the validity of this theorem has been shown in high frequency for targets whose RCS is produced by elementary interactions (specular reflection in particular). We are interested in aerial platforms and in particular some Low Observable targets that have relatively "pure" geometries limiting the presence of complex interactions. Several variants of the MBT from the field of electromagnetism [1][2][3] and acoustics [4] are used. Their performances are compared from data obtained from a MoM method that is recognized to produce accurate scattering data. To highlight the discrepancies produced by the different variants, we use both a metric to compare the quality of the bistatic holograms obtained and also radar imaging which allows locating the areas of the target where the echoes are not correctly restored.
The growth of connected mobile devices in the current network and new applications such as real-time communication, video streaming and others, exponentially increases the throughput demand. The proposed paper presents a numerical and experimental study of propagation and coverage on a 91 m² indoor environment at 24.15 GHz. The numerical analysis has been made with the support of Altair WinProp™ software in order to estimate the environment coverage map. The numerical study is experimentally validated by collecting error vector magnitude (EVM) measurements, in specific positions, of a 160 Mbit/s QAM signal. The transmission is made by a 12-dBi gain omnidirectional slotted waveguide antenna array with approximately 1 GHz of operational bandwidth. Experimental results presented a 40% coverage for EVM below 12%.
The Conex Antenna, Radar, and Measurement Equipment Lab (CARAMEL) is a ten-element VHF antenna array that operates from 30 MHz-120 MHz with an attached lab space. This array was developed for use in low frequency Radar Cross Section (RCS) measurements. The antenna elements support both vertical and horizontal polarizations. The antenna was designed using a genetic algorithm, employing the fragmented aperture technique; measured and modeled data will be presented. The attached lab space is air conditioned and provisioned for rack mounted equipment. The structure uses a modified 20' Conex shipping container where an entire sidewall has been replaced with a reinforced composite radome for the antennas. The overall mechanical frame design included a Finite Element Analysis to ensure structural integrity. The system is intended for long-term standalone use as an outdoor measurement radar system but can be moved using standard shipping container methods. The structure was shipped using a standard cargo carrier from Atlanta, Georgia to White Sands, New Mexico.
In this paper, the concept of a new S-band dual-polarized dielectric rod antenna is discussed. The antenna is composed of two concentric dielectric cylinders. The inner dielectric presents high dielectric constant, while the outer has a lower dielectric constant. Given this configuration, the resulting antenna provides high gain, narrow beamwidth, large bandwidth, and very low cross-polarization. In addition, the antenna is lower size in the transversal dimensions, and is predicted to be lighter than other antennas that provide equivalent performance, especially at low frequencies (S-band). An antenna with such an architecture can be 3D-printed, and therefore, the cost for the fabrication are considerable low. Numerical results of the antenna performance are presented and discussed.
Shipboard phased array radar antennas typically have high gain, low sidelobe specifications, and testing after initial production, overhaul or repair often reveals sidelobes that fail specifications, requiring rework. Further, some systems only allow phase adjustments as a means to fine tune the pattern. To correct sidelobe failures in these systems, the phase distribution of the array is first mapped using near-field scanning techniques, then specific element phases are adjusted, such as by using phase shifters. The standard method of determining phase changes has been based on trying to achieve a nominal phase profile; however, this method does not allow targeting specific problematic sidelobes. The authors have developed a novel method, dubbed "Whack-a-Lobe", which targets suppression of specific sidelobes while minimizing other impacts to the pattern. Recognizing that far-field sidelobes are a summation of complex vectors of the individual elements in the direction of the sidelobe, the authors have developed a cross product technique that identifies elemental vectors orthogonal to a far-field sidelobe vector such that only a minimal phase change to these elemental vectors is needed to reduce the sidelobe level. This technique is targeted, deterministic, and reduces tuning cycles, labor hours and antenna test chamber time.
Antenna gain is the product of directivity and antenna loss. Antenna gain is typically measured by comparing the antenna under test (AUT) to a standard gain horn (SGH) or direct gain measurement using a calibrated probe. This requires an accurate account of power into the AUT and SGH, the loss of all test cables and switches must be measured to obtain an accurate AUT gain. Additionally, SGH calibration uncertainty reduces the quality of the measurement. The gain measurement technique describe here exploits the near-field range capability of accurately producing the pattern of high gain antennas. The near-field range allows the full wave capture of antenna aperture fields and transformation to the far-field with high resolution. The new technique uses the directivity obtained by integrating the far-field pattern, accounts for the spill-over energy not measured by the near-field range, and uses measured network losses of the AUT. It does not require measured losses of test cables and switches. Since AUT losses are typically measured as part of antenna integration the technique reduces overall measurement burden. Accurate calculation of spill-over energy is the key to success. The technique has been shown to yield better accuracy than the typical gain calibration method for multi-beam high gain antennas.
Planar near-field ranges are popular facilities to evaluate far-field antenna patterns. These ranges typically have the scanner plane parallel to the Antenna Under Test (AUT). Having the scanner plane parallel to the AUT can limit the maximum far-field angles that can be properly measured due to the mechanical extents over which the range can accommodate. This paper summarizes a test approach where the AUT is rotated in the near-field such that sufficient energy is concentrated within the range extents, ultimately resulting in an accurate far-field pattern. Measured results will be shown which demonstrate the limitations of the current testing approach, as well as the benefits of the near-field rotation approach.
Empirical optimization of software reconfigurable antennas having hundreds of degrees of freedom demands rapid measurement, especially when multiple objectives, e.g. gain at multiple angles and polarizations, are included. This paper describes a measurement technique and process flow for rapid optimization of antenna performance. Previously, such evaluation with mechanical scanning was slow and impractical. The technique is enabled by closed-loop automation of an electronically scanned near field measurement system that determines the hemispherical radiation pattern of a given antenna state in approximately 1 second. In this way thousands of antenna states are evaluated per hour. This paper presents measurements of antenna states optimized using the new technique, and results are compared to measurements of states optimized by the usual far field technique.
A hybrid method that combines the finite element method (FEM), the Floquet mode analysis and the shooting and bouncing ray method (SBR) is presented to solve the quiet-zone field in large tapered anechoic chambers. In the method, the field equivalence principle is employed to replace the throat of the tapered chamber by a set of equivalent electric and magnetic currents. The Floquet mode analysis is employed to approximate the rest of the absorber lined walls by virtual surfaces with equivalent reflection coefficients. The total quiet-zone field then becomes the superposition of the field radiated by the equivalent currents, and the field scattered by the virtual reflective surfaces. The scattered field is calculated from the SBR method. The required equivalent currents of the throat and the reflection coefficients of absorber array walls are computed with the use of the FEM, which allows the considerations of the complex structure and near-field interaction. Numerical examples are presented to demonstrate the feasibility of the proposed method.
NB-IoT (Narrowband Internet of Things) is a narrowband radio technology showing very different characteristics compared with traditional wireless protocols. For the first time based on authors' best knowledge, this paper compares the Over-the-Air (OTA) performance of NB-IoT in the Reverberation Chamber (RC) and Anechoic Chamber (AC), which involves two major RF test environment variations in the OTA test arena. In this paper, the Total Radiated Power (TRP) and Total Isotropic Sensitivity (TIS), related to the transmitter and receiver performance of NB-IoT, respectively, are investigated. For TIS test, an early exit algorithm with 95% confidence level based on Chi-Square distribution has been developed to improve the test speed. The test results show a good match (Within CTIA allowed measurement uncertainty) between AC and RC. Our analysis also includes several key parameters, such as test repeatability, measurement uncertainty, and test time, which gives a comprehensive comparison of different aspects between RC and AC for NB-IoT OTA test. It could be noticed as well that the early exit algorithm based on Chi-Square distribution improves the test time performance significantly without compromising the test accuracy.
This paper discusses some aspects of isolation improvement and associated measurements on a cylindrical millimeter-wave repeater operating over K, Ka and V bands. The isolation between the transmitting and receiving antennas is improved by means of reactive impedance surface implemented as tapered depth corrugations. The designed tapered depth profile broadens bandwidth of the surface compared to the traditional quarter wavelength corrugations. Required isolation of 80 dB and large electrical size of the platform make numerical analysis and actual measurements challenging. Details of the analysis and measurements are summarized. Along with external coupling, the coupling due to leakages from waveguide components and antennas is also discussed. Measurements confirm that the design goal isolation is accomplished.
This paper presents the second phase of the development of a new measurement technique to determine antenna system noise temperature using data acquired from a planar near-field measurement. In the first phase, it was shown that the noise temperature can be obtained using the plane-wave spectrum of the planar near-field data and focusing on the portion of the spectrum in the evanescent region or "imaginary space". Actual evanescent modes are highly attenuated in the latter region and therefore the spectrum in this region must be produced by "errors" in the measured data. Some error sources such as multiple reflections will produce distinct localized lobes in the evanescent region and these are recognized and correctly identified by using a data point spacing of less than /2 to avoid aliasing errors in the far-field pattern. It has been observed that the plane wave spectrum beyond these localized lobes becomes random with a uniform average power. This region of the spectrum must be produced by random noise in the near-field data that is produced by all sources of thermal noise in the electronics and radiated noise sources received by the antenna. By analysing and calibrating this portion of the spectrum in the evanescent region the near-field noise power can be deduced and the corresponding noise temperature determined. In the current phase of tests, planar near-field data has been acquired on a measurement system and the analysis applied to determine the system noise parameters. Measurements have been performed with terminations inserted at three different locations in the RF receiving path: the IF input to the receiver, the input to the mixer and the input to the probe that is transmitting to a centre-fed reflector antenna. The terminations consist of either a load that serves as the "cold" noise source or a noise source with a known noise output for the "hot" noise source.